-150x150w.jpg)
Iveco EURO 6 | Fault DTC Cleaner | Error Code Cleaner
-500x500.jpg "Iveco EURO 6 | Fault DTC Cleaner | Error Code Cleaner")
-500x500.jpg "Iveco EURO 6 | Fault DTC Cleaner | Error Code Cleaner")
-500x500.jpg "Iveco EURO 6 | Fault DTC Cleaner | Error Code Cleaner")
-500x500.jpg "Iveco EURO 6 | Fault DTC Cleaner | Error Code Cleaner")
-107x107.jpg "Iveco EURO 6 | Fault DTC Cleaner | Error Code Cleaner")
-107x107.jpg "Iveco EURO 6 | Fault DTC Cleaner | Error Code Cleaner")
-107x107.jpg "Iveco EURO 6 | Fault DTC Cleaner | Error Code Cleaner")
-107x107.jpg "Iveco EURO 6 | Fault DTC Cleaner | Error Code Cleaner")
- Error Code Cleaner / Eraser for Iveco Trucks Euro 6. Pocket Size.
- : In Stock! Estimated Delivery Time: 2-4 Days
- Brand: BALTICDIAG
- Model: IcomER_E6
- SKU: BD10430
Error Code Cleaner / Eraser for Iveco Euro 6. Pocket Size.
The offered Error Code Cleaner is a standalone device. Using it is very easy and fast, just follow these steps:
- Turn ignition ON.
- Connect the device to the diagnostic connector of the vehicle.
- The Working/Done lamp starts blinking, wait until it lights up permanently green.
- Switch ignition OFF and disconnect the eraser. That's all!
- All inactive errors from supported systems are cleared.
Iveco Euro 6 Eraser supported systems:
- Engine including Aftertreatment System
- Brakes - EBS
- Vehicle ECU VCM
- Tachograph (DTCO)
- Automatic Gearbox
- Retarder
Supported Models:
- Stralis
- EuroCargo
- HI-WAY
This device also supports disabling torque reduction/speed reduction after Exhaust Aftertreatment System Failure!
The Error Code Cleaner checks the connection with the vehicle. If there is no connection with the vehicle, it informs about it with the "Error" indicator. Thanks to this, you can be sure that unwanted errors have been removed!
The Error Code Cleaner is equipped with three controls:
- Power: It is always lit when the Cleaner has power supply from the diagnostic connector.
- Working/Done: This LED blinks when the eraser is working and is permanently on when the eraser finishes its work successfully.
- Error: It is permanently on if there is no connection with the vehicle or blinks when the device is connected to an unsupported vehicle.
What is the DTC Cleaner?
The DTC Cleaner is a device that effectively removes inactive errors or faults from a vehicle. It functions similarly to a diagnostic tool and needs to be connected to the OBD (On-Board Diagnostics) port. Once connected, it scans the vehicle's components by directly accessing their control units and clears any errors they may be displaying.
Why use a DTC Cleaner?
The DTC Cleaner proves invaluable when drivers need to erase faults on the go, especially those caused by faulty vehicle components. It requires no expertise in diagnostics as it can be effortlessly plugged in to do the job for the driver.
For instance, in cases where faults occur in the SCR (Selective Catalytic Reduction) system, drivers often find themselves restricted by a capped vehicle speed (Limp mode) after a specific duration, with the vehicle stuck in a single gear and limited to a maximum speed of 15-30 mph, resulting in sluggish performance, especially when carrying heavy loads.
Our DTC Cleaner can reset the Limp mode timer for the vehicle, allowing the driver to complete their tasks and conveniently reach a service center. If immediate SCR repairs are not feasible, worry not; you can use the DTC Cleaner as many times as needed until you're ready to address the SCR system repair.
What errors does it clear?
The DTC Cleaner functions like a "Clear All" button on a diagnostic system, enabling the clearance of any other inactive errors present in the vehicle. However, it cannot resolve errors resulting from active physical faults within the vehicle.
For specific information on the units to which the DTC Cleaners can connect and the faults they can clear, please feel free to contact us.
-120x100w.jpg "LAUNCH")
