-150x150w.jpg)
Volvo Trucks all models Euro 6 From 2013 | Fault DTC Cleaner | Error Code Cleaner
-500x500.jpg "Volvo Trucks all models Euro 6 From 2013 | Fault DTC Cleaner | Error Code Cleaner")
-500x500.jpg "Volvo Trucks all models Euro 6 From 2013 | Fault DTC Cleaner | Error Code Cleaner")
-500x500.jpg "Volvo Trucks all models Euro 6 From 2013 | Fault DTC Cleaner | Error Code Cleaner")
-500x500.jpg "Volvo Trucks all models Euro 6 From 2013 | Fault DTC Cleaner | Error Code Cleaner")
-107x107.jpg "Volvo Trucks all models Euro 6 From 2013 | Fault DTC Cleaner | Error Code Cleaner")
-107x107.jpg "Volvo Trucks all models Euro 6 From 2013 | Fault DTC Cleaner | Error Code Cleaner")
-107x107.jpg "Volvo Trucks all models Euro 6 From 2013 | Fault DTC Cleaner | Error Code Cleaner")
-107x107.jpg "Volvo Trucks all models Euro 6 From 2013 | Fault DTC Cleaner | Error Code Cleaner")
- Error Code Cleaner / Eraser for Volvo Trucks all models from 2013 till now.. Pocket Size
- : In Stock! Estimated Delivery Time: 2-4 Days
- Brand: BALTICDIAG
- Model: VcomER_E6_CB
- SKU: BD10544
Error Code Cleaner / Eraser for Volvo Trucks all models from 2013 till now. Pocket Size.
Offered Error Code Cleaner is standalone device. Using of it is very easy and fast, just:
- Turn ignition ON
- Connect Device to diagnostic connector of the vehicle.
- Working/Done lamp starts blinking, wait until lights up permanently green.
- Switch ignition OFF and disconnect eraser, that's all!
All inactive errors from supported systems are cleared!
Scania Eraser supported systems:
- EMS - Engine ECU
- VMCU - Vehicle Master Control Unit
- ACM -Aftertreatment Control Module
- RET - Retarder
- TECU -Automatic Transmission
- BBM - Body Builder Module
- CCIOM - Central Module
- CCM - Air Condidioning
- CIOM - Cabin Modele
- DACU - Driver Assistace Control Module
- DDM - Driver door Module
- DTCO - Tachograph
- EBS - Brake System
- FAS -
- FCIOM - Front frame Module
- FLS - Radar
- HMIIOM - Multimedia Display
- IC - Instruments
- LECM -
- LPOS - System Laneguard
- PDM -Passanger door Module
- RCIOM - Rear Controle Module
- SID -
- TGW2 -Telematic Gateway
- VS -
- WRC -
- All systems are supported
Supported Models (Series):
- FH (4)
- FM (4)
- FH16 (4)
- FMX (4)
- FH (4) Euro 5
- FM (4) Euro 5
- All Volvo Models with Electrical System V4.
This Device supports disabling Torque reduction / Speed reduction after Exhaust Aftertreatment System Failure !
The Error Code Cleaner check connection with the vehicle. If there is no connection with vehicle it inform about it with the "Error" indicator. Thanks to this you can be sure that unwanted errors have been removed!
Error Code Cleaner is equipped with tree controls:
- Power - is always Light when Cleaner have Power supply from diagnostic connector
- Working/Done - this LED blinks when eraser is working and is permanently on when eraser finishes work with success
- Error - is permanently ON if there is no connection with vehicle or blinks when device is connected to unsupported vehicle
What is the DTC Cleaner?
The DTC Cleaner is a device that effectively removes inactive errors or faults from a vehicle. It functions similarly to a diagnostic tool and needs to be connected to the OBD (On-Board Diagnostics) port. Once connected, it scans the vehicle's components by directly accessing their control units and clears any errors they may be displaying.
Why use a DTC Cleaner?
The DTC Cleaner proves invaluable when drivers need to erase faults on the go, especially those caused by faulty vehicle components. It requires no expertise in diagnostics as it can be effortlessly plugged in to do the job for the driver.
For instance, in cases where faults occur in the SCR (Selective Catalytic Reduction) system, drivers often find themselves restricted by a capped vehicle speed (Limp mode) after a specific duration, with the vehicle stuck in a single gear and limited to a maximum speed of 15-30 mph, resulting in sluggish performance, especially when carrying heavy loads.
Our DTC Cleaner can reset the Limp mode timer for the vehicle, allowing the driver to complete their tasks and conveniently reach a service center. If immediate SCR repairs are not feasible, worry not; you can use the DTC Cleaner as many times as needed until you're ready to address the SCR system repair.
What errors does it clear?
The DTC Cleaner functions like a "Clear All" button on a diagnostic system, enabling the clearance of any other inactive errors present in the vehicle. However, it cannot resolve errors resulting from active physical faults within the vehicle.
For specific information on the units to which the DTC Cleaners can connect and the faults they can clear, please feel free to contact us.
-120x100w.jpg "LAUNCH")
